Damped free vibrations (2024)

Next post Previous post

April 12, 2014 at 1:03 AM by Dr. Drang

The second simplest vibrating system is composed of a spring, a mass, and a damper.

Damped free vibrations (1)

We’ve seen the spring and the mass before, so let’s talk about the damper.

The image typically used to represent a damper is meant to look like the cross-section of a hydraulic cylinder1 with a leaky piston, a device called a dashpot. You’re supposed to imagine the fluid in the cylinder squirting around the edges of the piston; it doesn’t stop the movement of the piston, but it does slow it down. Strictly speaking, this kind of damping is called viscous damping, but the word viscous is often dropped.

The force exerted by a dashpot is proportional to the speed at which the piston moves and is directed in opposition to the movement, so when we construct the free-body diagram of the mass, assuming both displacement and velocity in the positive uu direction, we get the figure on the right and this equation of motion:

kucu˙=mu¨-ku - c \dot u = m \ddot u

where cc is the constant of proportionality between the damper’s force and the speed at which it’s extended or retracted. The other symbols have the same meaning as in the undamped case.

Rearranging into the usual form,

mu¨+cu˙+ku=0m \ddot u + c \dot u + k u = 0

we get a second order, linear differential equation with constant coefficients. This is—lucky us—one of the differential equation forms that can actually be solved without resorting to numerical methods. It’s common to divide through by mm and introduce some new variables.

u¨+2ζωnu˙+ωn2u=0\ddot u + 2 \zeta \omega_n \dot u + \omega_n^2 u = 0

where

ωn=km\omega_n = \sqrt{\frac{k}{m}}

is the undamped natural frequency of the system, which we’ve seen before, and

ζ=c2mωn=c2km\zeta = \frac{c}{2m\omega_n} = \frac{c}{2\sqrt{km}}

is the damping coefficient.2 It is a dimensionless quantity, because cc has the units

c[FLT1]=[MLT2LT1]=[MT]c \rightarrow \left [\frac{F}{LT^{-1}} \right ] = \left [ \frac{MLT^{-2}}{LT^{-1}} \right ] = \left [ \frac{M}{T} \right ]

and so does 2mωn2 m \omega_n.

The quantity 2mωn2m \omega_n is called the critical damping constant, ccc_c. The damping coefficient is therefore often defined this way:

ζ=ccn\zeta = \frac{c}{c_n}

What makes critical damping critical? From a mathematical point of view, critical damping represents a change in the the nature of the solution of the differential equation. John Cook did a good job explaining that in his post on damped vibrations, so I’ll just refer you there. From a physical point of view, critical damping represents the boundary between oscillatory behavior and non-oscillatory behavior. The system oscillates about the equilibrium position only if the damping is less than critical: c<ccc < c_c or ζ<1\zeta < 1. This is called the underdamped case and is the one we’ll be exploring.3

The oscillatory solution can be written as

u=eζωnt(u0cosωdt+v0+ζωnu0ωdsinωdt)u = e^{-\zeta \omega_n t} \left( u_0 \cos \omega_d t + \frac{v_0 + \zeta \omega_n u_0}{\omega_d} \sin \omega_d t \right)

where u0u_0 and v0v_0 are the displacement and velocity at t=0t = 0, and

ωd=1ζ2ωn\omega_d = \sqrt{1 - \zeta^2}\,\,\omega_n

is called the damped frequency for reasons that will become clear soon. The solution can also be written more compactly as

u=Aeζωntcos(ωdtϕ)u = A e^{-\zeta \omega_n t} \cos(\omega_d t - \phi)

You may recall from our look at undamped free vibrations that the phase angle, ϕ\phi, is somewhat arbitrary—it’s value is determined by when we decide to say t=0t = 0. Therefore, we can choose a starting time that makes ϕ=0\phi = 0 and simplify our equations and graphs even more.

The solution for ϕ=0\phi = 0 and ζ=0.1\zeta = 0.1 looks like this, a decaying sinusoid:

Damped free vibrations (2)

The exponential term acts as an envelope that lowers the amplitude of the oscillation as time marches on. The points of tangency, where the black solution curve touches the dashed blue envelope, are where cosωdt=1\cos \omega_d t = 1. The upper points of tangency are spaced

Td=2πωd=2π1ζ2ωnT_d = \frac{2\pi}{\omega_d} = \frac{2 \pi}{\sqrt{1 - \zeta^2}\,\,\omega_n}

apart, as are the lower points of tangency. TdT_d is the damped period of the system. For small values of ζ\zeta, TdTnT_d \approx T_n and ωdωn\omega_d \approx \omega_n.

If you zoom in, you can see that the maxima and minima of the curve don’t quite match up with the points of tangency.

Damped free vibrations (3)

It can be shown, however, that the time between successive maxima (or successive minima) is the same as the time between successive points of tangency. This is very convenient if you want to measure the damped period of a system experimentally. When you’re monitoring the vibration of a system, the maxima and minima are relatively easy to determine—the points of tangency are impossible.

Similarly, the amplitude ratio between successive maxima is equal to the amplitude ratio between successive upper tangency points. If we call each maximum umu_m, where mm is an integer, then

umum+1=eζωnteζωn(t+2π/ωd)=e2πζωn/ωd\frac{u_m}{u_{m+1}} = \frac{e^{-\zeta \omega_n t}}{e^{-\zeta \omega_n (t + 2 \pi/\omega_d)}} = e^{2\pi\zeta\omega_n/\omega_d}

If we take the natural logarithm of both sides, we get

δ=ln(umum+1)=2πζωnωd=2πζ1ζ2\delta = \ln \left( \frac{u_m}{u_{m+1}} \right) = \frac{2\pi\zeta\omega_n}{\omega_d} = \frac{2\pi\zeta}{\sqrt{1-\zeta^2}}

which is called the log decrement of the damped oscillation. We can determine the damping coefficient experimentally by measuring the displacement at successive maxima, taking the natural log of their ratio (that’s δ\delta), and calculating ζ\zeta by a rearrangement of the above equation:

ζ=δ24π2+δ2\zeta = \sqrt{\frac{\delta^2}{4\pi^2 + \delta^2}}

I’ve always thought of the damping coefficient and log decrement as conceptually similar to the coefficient of restitution of a bouncing ball. In both cases, we’re tracking the decay of successive “high points” in the motion of an object. They also represent a loss of mechanical energy from the system, a point we’ll discuss in a later post.

When we looked at undamped systems, we found that their behavior is governed by their natural frequency, ωn\omega_n, and that we can determine ωn\omega_n experimentally without knowing either kk or mm. Now we see that the behavior of a damped system is governed by ωd\omega_d and ζ\zeta4 and that we can determine them experimentally without knowing kk, mm, or cc.

Mechanical systems have springy parts and they have mass, but very few have actual dashpots. What good is all this math if it doesn’t represent actual equipment? We’ll talk about the kinds of real-world things we model as dashpots next time.

  1. This is sort of like the kind of hydraulic cylinders you see on construction equipment, but it isn’t being driven by pumps. All the fluid stays in the cylinder—it just moves from one side of the piston to the other as the piston moves back and forth.

  2. In case you’re rusty with your Greek alphabet, that’s the letter zeta.

  3. Although it’s called underdamped, you shouldn’t think of it as having some deficiency. There can be plenty of damping in an underdamped system. The “under” just means the system oscillates.

  4. And the natural frequency, but once we have the damped frequency and the damping coefficient, the natural frequency is easy to calculate.

Next post Previous post

Damped free vibrations (2024)

References

Top Articles
Latest Posts
Recommended Articles
Article information

Author: Chrissy Homenick

Last Updated:

Views: 5933

Rating: 4.3 / 5 (74 voted)

Reviews: 81% of readers found this page helpful

Author information

Name: Chrissy Homenick

Birthday: 2001-10-22

Address: 611 Kuhn Oval, Feltonbury, NY 02783-3818

Phone: +96619177651654

Job: Mining Representative

Hobby: amateur radio, Sculling, Knife making, Gardening, Watching movies, Gunsmithing, Video gaming

Introduction: My name is Chrissy Homenick, I am a tender, funny, determined, tender, glorious, fancy, enthusiastic person who loves writing and wants to share my knowledge and understanding with you.